Navyug Enterprises

• Suitable for Modular mounting
• Steel bowl guard, Bayonet type
• Internal Autodrain
• Float type, no electrical connections required
• Provided with manual drain
• Provision for drain tube connection, to take the condensate away from the unit, to keep the working area clean
• Bronze filtering element
• Separator and shield for efficient moisture separation

• Note the direction of flow before installation and connect piping accordingly.
• Flush pipings for dirt, dust, rust and other foreign particles.
• Install in clean atmosphere.
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape does not enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer.
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene, kerosene or other aromatic hydrocarbons.

• Modular type for easy and fast maintenance
• Suitable for wall mounting
• Filter
• Bronze filtering element
• Separator and shield for efficient moisture separation
• Press type manual drain for easy operation
• Regulator
• Diaphragm operated, relieving type
• Pressure compensated by Balanced poppet
• Flow compensated in models FRLM14, FRLM15 and FRLM17 for faster response
• Non raising Press to Lock adjusting knob for locking at any set pressure
• Lubricator
• Fog/Mist type Lubricator
• Fine adjustment of lubrication
• Lubrication proportional to flow
• Steel bowlguard, bayonet type on FRLM14, FRLM15 and FRLM17 models and threaded type on FRLM13 model
• Good flow and regulating characteristics

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape doesnot enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene, kerosene or other aromatic hydrocarbons

• Set pressure selectable (Mpa, psi, kgf/cm2, bar)
• Both upper and lower limits of pressure can be set independently
• Panel mountable
• Direct mountable
• Both PNP & NPN versions
• Two outputs

• 2 Colours display (Red / Green)
• Set pressure selectable (kPa, psi, kgf/cm2, bar)
• Both upper and lower limits of pressure can be set independently
• Panel mountable
• Direct mountable
• Both PNP & NPN versions
• Single output

• Individual unit (Externally mountable)
• Low operating pressure
• Compact size
• Elegant design and finish
• Long life

• These Auto drain units are externally mountable on G1/4, 3/8 and 1/2, 3/4, 1 size Filters and FRC units.
• As the condensed water collects in the drain unit, the float moves up and drains the water. The condensate water can also be drained manually.
• A plastic tube can be fitted at the bottom of the auto drain unit to take the drained water away from the unit.

• Suitable  for manifold mounting
• Mounting provision for individual unit
• Compact size
• Manual override
• Wide range  of  manifolds  available
• Wide range of coil voltages

• Modular mounting with FRL
• Port thread at both ends
• Sizes - G1/4, G3/8 & G1/2
• Window display to show the valve position ( i.e.) the valve is in On condition or Off condition.

• Opening and closing of airline with relieving of down stream pressure at closed condition.
• The valve can be locked at the closing condition (Exhaust 2 - 3).

• Modular type for easy and fast maintenance.
• Suitable for wall mounting.

• Bronze filtering element.
• Separator and shield for efficient moisture separation.
• Press type manual drain for easy operation

• Diaphragm operated, relieving type.
• Pressure compensated by balanced poppet.
• Flow compensated ( with venturi ) in models FRLM14,
• FRLM15 and FRLM17 for faster response.
• Non raising ' Press to lock ' adjusting knob for locking at any set pressure.

• Fog / Mist type Lubricator.
• Fine adjustment of lubrication.
• Lubrication proportional to flow.
• Steel bowl guard, bayonet type on FRLM14 ,FRLM15 & FRLM17 models and threaded type on FRLM13 model.
• Good flow and regulating characteristics.

• 3/2, 5/2, 5/3 valves
• Suitable for manifold mounting
• Mounting provision for individual unit
• Compact size
• Manual override
• Wide range of manifolds available
• wide range of coil voltages

Model No: G1/8

• adjustable cushioning at both ends with elastomer pads
• wide varieties of mountings as per iso 15552 / vdma 24562 standards
• magnetic and non magnetic version
• aluminium profile (square) cylinder barrel
• magnetic sensor common for all sizes (refer magnetic sensor catalogue)
• optional - high temperature (viton seals) 150°c max.
• optional - non corrosive stainless steel piston rod and piston rod lock nut (ss 304)

model no: A23, A24

• Adjustable cushioning at both ends with elastomer pads
• Wide varieties of mountings
• Magnetic and Non magnetic version
• Optional - High temperature (Viton seals) 150°C max.
• Optional - Non corrosive Stainless steel piston rod and piston rod lock nut (SS 304)

Model No: A27, 28

We offer a wide range of Pneumatic Silencers, carefully designed by professional designers to keep the environment clean. Our products have engraved a remarkable place in national market and are in great in demands as we manufacture them with the use of best quality material.

• Button, Conical, Silencer cum flow control (with lock nut),
• Silencer cum flow control (with spring)
• Sizes :M5,1/8,1/4,3/8,1/2
• Good flow and Silencing characteristics
• Brass body and Sintered bronze silencer elements

• Conforms to ISO 5782-1
• Suitable for Modular mounting
• Steel bowl guard, bayonet type on F14, F15 & F17 models and threaded type on F13 model
• Press type Manual drain for easy operation
• Bronze filtering element
• Separator and shield for efficient moisture separation

• Note the direction of flow before installation and connect piping accordingly.
• Flush pipings for dirt, dust, rust and other foreign particles.
• Install in clean atmosphere.
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape does not enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer.
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene, kerosene or other aromatic hydrocarbons.

• Modular type
• Suitable for panel mounting
• Filter
• Bronze filtering element
• Separator and shield for efficient moisture separation
• Bayonet type steel bowl guard
• Internal auto drain
• Float type, no electrical connections required
• Provided with manual drain
• Provision for drain tube connection, to take the condensate away from the unit, to keep the working area clean
• Regulator
• Diaphragm operated, relieving type
• Pressure compensated by balanced poppet
• Flow compensated for faster response
• Non raising Press to lock adjusting knob for locking at any set pressure
• Good flow and regulating characteristics

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape does not enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene kerosene or other aromatic hydrocarbons

• Modular type
• Suitable for panel mounting
• Filter
• Bronze filtering element
• Separator and shield for efficient moisture separation
• Press type manual drain for easy operation
• Suitable for automatic drain
• Regulator
• Diaphragm operated, relieving type
• Pressure compensated by balanced poppet
• Flow compensated
• Non raising Press to lock adjusting knob
• Aluminium bowl guard, bayonet type (3/4 and 1" only)
• Good flow and regulating characteristics

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples with taper threads ( R ) to be used with teflon tape. Ensure teflon tape does not enter the unit during tightening. Nipples with straight threads ( G ) to be used with sealing washer.

• Modular type
• Suitable for panel mounting
• Filter
• Bronze filtering element
• Separator and shield for efficient moisture separation
• Bayonet type steel bowl guard
• Internal Autodrain
• Float type, no electrical connections required
• Provided with manual drain
• Provision for drain tube connection, to take the condensate away from the unit, to keep the working area clean
• Regulator
• Diaphragm operated, relieving type
• Pressure compensated by balanced poppet
• Flow compensated ( with venturi ) for faster response
• Non raising Press to lock adjusting knob for locking at any set pressure
• Good flow and regulating characteristics

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape doesnot enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene, kerosene or other aromatic hydrocarbons.

• Elastomer cushioning at both ends.
• Wide varieties of mountings.
• Accessories
• Magnetic and Non magnetic versions
• Low friction.
• Long life.

• adjustable cushioning at both ends
• wide varieties of mountings
• long life
• magnetic and non magnetic versions

Model No: A10, A11

• Adjustable cushioning at both ends with elastomer pads
• Wide varieties of mountings as per ISO 15552 / VDMA 24562 standards
• Magnetic and Non magnetic version
• Aluminium profile (square) cylinder barrel
• Magnetic sensor common for all sizes (Refer Magnetic sensor catalogue)
• High temperature (Viton seals) 150°C max.
• Non corrosive Stainless steel piston rod and piston rod lock nut (SS 304)

• Available in two versions
• Low cracking and closing pressure
• Bubble tight - elastomer seat
• Plastic portion can be turned by 360°
• Teflon pre-coated male taper threads

• Pilot  operated  non-return  valve  is  used  for  stopping  the  cylinder  in  intermediate  position.  So  long  as  a  pilot  signal  is applied, air is free to flow to and from the cylinder. When the pilot signal is removed, the valve acts as a conventional non- return valve and prevents air from exhausting from the cylinder, thus stopping movement.

• While ordering Pilot operated non-retsurn valve, mention the ordering number given in the corresponding tables.

• Elastomer  end  cushioning
• Wide  varieties  of  mountings
• Space  saving
• Magnetic and Non magnetic version
• Aluminium  profile  (square)  cylinder  barrel
• Magnetic sensor common for all sizes (Refer Magnetic sensor catalogue )

• Modular type for easy and fast maintenance
• Suitable for wall mounting
• Filter
• Bronze filtering element
• Separator and shield for efficient moisture separation
• Press type manual drain for easy operation
• Regulator
• Diaphragm operated, relieving type
• Pressure compensated by Balanced poppet
• Flow compensated in models FRLM14, FRLM15 and FRLM17 for faster response
• Non raising Press to Lock adjusting knob for locking at any set pressure
• Lubricator
• Fog/Mist type Lubricator
• Fine adjustment of lubrication
• Lubrication proportional to flow
• Steel bowlguard, bayonet type on FRLM14, FRLM15 and FRLM17 models and threaded type on FRLM13 model
• Good flow and regulating characteristics

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape doesnot enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene, kerosene or other aromatic hydrocarbons.

• For higher pressure range above 10 bar
• Suitable for Modular mounting
• Aluminium bowl guard, bayonet type (3/4 and 1" only)
• Press type Manual drain for easy operation
• Suitable for Internal autodrain also
• Bronze filtering element
• Separator and shield for efficient moisture separation

• Note the direction of flow before installation and connect piping accordingly.
• Flush pipings for dirt, dust, rust and other foreign particles.
• Install in clean atmosphere.
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape does not enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer.
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene, kerosene or other aromatic hydrocarbons.

• For higher pressure range above 10 bar
• Suitable for Modular mounting
• Fog / mist type
• Fine adjustment of lubrication
• Aluminium bowl guard, bayonet type (3/4 and 1_ only)
• Lubrication proportional to flow

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples with taper threads ( R ) to be used with teflon tape. Ensure teflon tape does not enter the unit during tightening. Nipples with straight threads ( G ) to be used with sealing washer
• Oil may be filled when under pressure. However it is recommended to vent the air completely before filling the oil.

• Connecting thread at both ends
• Connection - G1/4, G3/8, G1/2
• Modular mounting with FRL

• Opening and closing of airline with relieving of the downstream pressure
• A window display to show the valve position when the valve is On condition (or) Exhaust condition