Air Preparation Units

• Modular type for easy and fast maintenance.
• Suitable for wall mounting.

• Bronze filtering element.
• Separator and shield for efficient moisture separation.
• Press type manual drain for easy operation

• Diaphragm operated, relieving type.
• Pressure compensated by balanced poppet.
• Flow compensated ( with venturi ) in models FRLM14,
• FRLM15 and FRLM17 for faster response.
• Non raising ' Press to lock ' adjusting knob for locking at any set pressure.

• Fog / Mist type Lubricator.
• Fine adjustment of lubrication.
• Lubrication proportional to flow.
• Steel bowl guard, bayonet type on FRLM14 ,FRLM15 & FRLM17 models and threaded type on FRLM13 model.
• Good flow and regulating characteristics.

• For higher pressure range above 10 bar
• Suitable for Modular mounting
• Aluminium bowl guard, bayonet type (3/4 and 1" only)
• Press type Manual drain for easy operation
• Suitable for Internal autodrain also
• Bronze filtering element
• Separator and shield for efficient moisture separation

• Note the direction of flow before installation and connect piping accordingly.
• Flush pipings for dirt, dust, rust and other foreign particles.
• Install in clean atmosphere.
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape does not enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer.
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene, kerosene or other aromatic hydrocarbons.

• Modular type
• Suitable for panel mounting
• Filter
• Bronze filtering element
• Separator and shield for efficient moisture separation
• Bayonet type steel bowl guard
• Internal auto drain
• Float type, no electrical connections required
• Provided with manual drain
• Provision for drain tube connection, to take the condensate away from the unit, to keep the working area clean
• Regulator
• Diaphragm operated, relieving type
• Pressure compensated by balanced poppet
• Flow compensated for faster response
• Non raising Press to lock adjusting knob for locking at any set pressure
• Good flow and regulating characteristics

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape does not enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene kerosene or other aromatic hydrocarbons

• Modular type
• Suitable for panel mounting
• Filter
• Bronze filtering element
• Separator and shield for efficient moisture separation
• Bayonet type steel bowl guard
• Internal Autodrain
• Float type, no electrical connections required
• Provided with manual drain
• Provision for drain tube connection, to take the condensate away from the unit, to keep the working area clean
• Regulator
• Diaphragm operated, relieving type
• Pressure compensated by balanced poppet
• Flow compensated ( with venturi ) for faster response
• Non raising Press to lock adjusting knob for locking at any set pressure
• Good flow and regulating characteristics

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples of taper threads ( R ) to be used with teflon tape. Ensure teflon tape doesnot enter the unit during tightening. Nipples of straight threads ( G ) to be used with sealing washer
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene, kerosene or other aromatic hydrocarbons.

• 2 Colours display (Red / Green)
• Set pressure selectable (kPa, psi, kgf/cm2, bar)
• Both upper and lower limits of pressure can be set independently
• Panel mountable
• Direct mountable
• Both PNP & NPN versions
• Single output

• Conforms to ISO 8573-1 standards
• Borosilicate filtering element
• 99.99% compressed filtered air upto 0.01micron to 0.1 micron
• Suitable for Modular mounting
• Steel bowl guard, bayonet type on FS15 model and threaded type on FS13 model
• Press type Manual drain for easy operation
• Separator for efficient moisture separation

• These type of mist separators are used in Chemical, Pharmaceutical, Food processing industry, Paint shops and for other precision pneumatic systems.

• Removes submicronic oil, water droplets and solid contaminants from compressed air.
• Used for high efficient filtration of compressed air, removing fine oil particles and droplets of sizes upto 0.01 microns

• Mount the mist seperator in line, next to a standard air filter series F1 with 5 micron filter element
• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples of taper threads (R) to be used with teflon tape. Ensure Teflon tape does not enter the unit during tightening. Nipples of straight threads (G) to be used with sealing washer
• Polycarbonate bowls may get damaged and possibly fail if exposed to synthetic oils, thinner, solvents, trichloroethylene kerosene or other aromatic hydrocarbons.

Series : FS1

• Mention the ordering number required

• Clamp for 3/8 Filter, Lubricator series F14, L14 - Ordering no : A2C32

• Modular mounting with FRL
• Port thread at both ends
• Window display to show the valve position

• Opening and closing of airline with relieving of downstream pressure at closed condition
• The valve can be locked at the closing condition (Exhaust 2 to 3)

• Modular mounting with FRL
• Port thread at both ends
• Sizes - G1/4, G3/8 & G1/2
• Window display to show the valve position ( i.e.) the valve is in On condition or Off condition.

• Opening and closing of airline with relieving of down stream pressure at closed condition.
• The valve can be locked at the closing condition (Exhaust 2 - 3).

• Mention the ordering number required

• Pressure Gauge for Regulator with Pressure range 0 - 10 bar : Ordering no : A2G02

• Conform to ISO 6953 1
• Suitable for panel and modular mountings
• Non raising Press to Lock adjusting knob for locking at any set pressure
• Diaphragm operated, relieving type
• Pressure compensated by balanced poppet
• Flow compensated in models R14 and R15 (with venturi) for faster response
• Good flow and regulating characteristics
• Built in non return valve allows free air flow in reverse direction. When the inlet air is reduced by and below the setup pressure

• Apart from its basic regulating characteristics in forward direction, this regulator with a built in non return valve allows free air flow in reverse direction, thus enabling to be used in applications requiring cylinders to exert two different force during extending and retracting strokes.

• Pull the knob and adjust by turning the knob clockwise to increase the pressure. Push the knob back to its locked position. ( Turning the knob counter clockwise will reduce the pressure )

• Note the direction of flow before installation and connect piping accordingly
• Flush pipings for dirt, dust, rust and other foreign particles
• Install in clean atmosphere
• Nipples with taper threads ( R ) to be used with teflon tape. Ensure Teflon tape doesnot enter the unit during tightening. Nipples with straight threads ( G ) to be used with sealing washer.

• Conforms to ISO 5782 -1
• Suitable for Modular mounting
• Steel bowl guard, bayonet type on F14, F15 &
• F17 models and threaded type on F13 model.
• Press type Manual drain for easy operation.
• Bronze filtering element.
• Separator and shield for efficient moisture separation.

• Note  the  direction  of  flow  before  installation  and  connect  piping  accordingly.
• Flush  pipings  for  dirt,  dust,  rust  and  other  foreign  particles.
• Install  in  clean  atmosphere.
• Nipples  of  taper  threads  (  R  )  to  be  used  with  teflon  tape.  Ensure  teflon  tape  does  not  enter  the  unit  during  tightening.
• Nipples  of  straight  threads  (  G  )  to  be  used  with  sealing  washer.
• Polycarbonate bowls  may get damaged  and  possibly  fail  if  exposed  to  synthetic  oils,  thinner,  solvents,  trichloroethylene, kerosene or other  aromatic  hydrocarbons.